Study of the bending modulus of individual silicon nitride nanobelts via atomic force microscopy

Analysis of the bending modulus of individual silicon nitride nanobelts in elastic regime is reported here. The nanobelts have the size between 200∼800 nm in width, and thickness 20∼50 nm. Atomic force microscopy was used to image and to perform measurements of force versus bending displacement on individual nanobelts suspending over strips. The bending modulus E_b is deduced by comparison of the measured force curves on the substrate and on the suspending nanobelts. It is shown that the elastic modulus of the silicon nitride nanobelts is about 570 GPa, which is much larger than that of bulk and film of the silicon nitride material. The larger elastic modulus is ascribed to the fact there are less structural defects in the silicon nitride nanobelts. PACS 81.70.Bt; 81.40.Lm; 61.80.+g     

Soliton and Periodic Travelling Wave Solutions for Quadratic Nonlinear Media

Many sets of the soliton and periodic travelling wave solutions for the quadratic χ^（2） nonlinear system are obtained by the Backlund transformation and the trial method. The property of the propagation for some travelling waves is investigated.     

Measurement of small-signal and large-signal responses of packaged laser modules at high temperature

In this paper, the pulsed injection method is extended to measure the chip temperature of various packaged laser modules, such as the DFB laser modules, the FP laser modules, and the EML laser modules. An optimal injection condition is obtained by investigating the dependence of the lasing wavelength on the width and period of the injection pulse in a relatively wide temperature range. The small-signal frequency responses and large-signal performances of packaged laser modules at different chip temperature are measured. The adiabatic small-signal modulation characteristics of packaged LD are first extracted. In the large-signal measurement, the effects of chip temperature, bias current and driving signal on the performances of the laser modules are discussed. It has been found that the large-signal performances of the EML modules depend on the different red-shift speeds of the DFB and EAM sections as chip temperature varying, and the optimal characteristics may be achieved at higher temperature.     

A Simple Bi-directional Mode Expansion Propagation Algorithm Based on Modes of a Parallel-plate Waveguide

The bi-directional mode expansion propagation algorithm (BEP) is known to be an accurate and efficient method for modelling field distribution in high-index contrast waveguide structures with strong back-reflections like Bragg gratings and photonic crystals. The main difficulty of this method is that for lossy structures, the propagation constants of modes are to be searched in the complex plane. To speed-up this procedure, a two-step algorithm for eigenmode calculation based on the expansion into the modes of an empty metallic waveguide has recently been proposed. Proper truncation rules possessing good convergence of the expansion method for both TE and TM modes have also been recently published. In this contribution, both these approaches are combined in the development of an extremely simple version of the two-dimensional BEP method that makes use of the field expansion into the eigenmodes of a parallel-plate waveguide. The method is strictly reciprocal and appeared to be computationally reliable also for strongly lossy structures. High numerical stability is ensured using the scattering matrix formalism, and an efficient method of calculating Bloch modes for symmetric as well as asymmetric periodic waveguide structures is adopted. A wide range of applicability of the method is demonstrated by a few examples.     

X射线荧光分析中X射线管原级能谱分布的测定

确切知道X射线管激发的原级能谱分布是X射线荧光分析中的一个重要前提,所用能谱分布函数的准确度大大影响了最终的测量结果。提出利用间接测量法,选用合适的参量模型来描述X射线的原级能谱分布。依靠实验测得的厚靶纯元素样品的荧光强度,利用已知的理论公式,建立非线性方程,优化得到参量模型中的参量值。通过比较实验测得的元素的荧光强度值和利用得到的能谱分布函数计算的理论值,证明此种方法是可行的。     

Crosslinkable poly(propylene carbonate): High‐yield synthesis and performance improvement

A crosslinking strategy was used to improve the thermal and mechanical performance of poly(propylene carbonate) (PPC): PPC bearing a small moiety of pendant C?C groups was synthesized by the terpolymerization of allyl glycidyl ether (AGE), propylene oxide (PO), and carbon dioxide (CO₂). Almost no yield loss was found in comparison with that of the PO and CO₂ copolymer when the concentration of AGE units in the terpolymer was less than 5 mol %. Once subjected to UV‐radiation crosslinking, the crosslinked PPC film showed an elastic modulus 1 order of magnitude higher than that of the uncrosslinked one. Moreover, crosslinked PPC showed hot‐set elongation at 65 °C of 17.2% and permanent deformation approaching 0, whereas they were 35.3 and 17.2% for uncrosslinked PPC, respectively. Therefore, the PPC application window was enlarged to a higher temperature zone by the crosslinking strategy. © 2006 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 5329–5336, 2006     

A copper‐based reverse atom‐transfer radical polymerization process for the living radical polymerization of polyacrylonitrile

The reverse atom‐transfer radical polymerization (RATRP) technique using CuCl₂/2,2′‐bipyridine (bipy) complex as a catalyst was applied to the living radical polymerization of acrylonitrile (AN). A hexasubstituted ethane thermal iniferter, diethyl 2,3‐dicyano‐2,3‐diphenylsuccinate (DCDPS), was firstly used as the initiator in this copper‐based RATRP initiation system. A CuCl₂ to bipy ratio of 0.5 not only gives the best control of molecular weight and its distribution, but also provides rather rapid reaction rate. The rate of polymerization increases with increasing the polymerization temperature, and the apparent activation energy was calculated to be 57.4 kJ mol^?1. Because the polymers obtained were end‐functionalized by chlorine atoms, they were used as macroinitiators to proceed the chain extension polymerization in the presence of CuCl/bipy catalyst system via a conventional ATRP process. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 226–231, 2006     

Synthesis of polyacrylonitrile via reverse atom transfer radical polymerization catalyzed by FeCl3/isophthalic acid

FeCl₃ coordinated by isophthalic acid was first used as a catalyst in the azobisisobutyronitrile‐initiated reverse atom transfer radical polymerization of acrylonitrile. N,N‐Dimethylformamide was used as a solvent to improve the solubility of the ligand. An FeCl₃‐to‐isophthalic acid ratio of 0.5 not only gave the best control of the molecular weight and its distribution but also provided rather a rapid reaction rate. The effects of different solvents on the polymerization of acrylonitrile were also investigated. The rate of the polymerization in N,N‐dimethylformamide was faster than that in propylene carbonate and toluene. The molecular weight of polyacrylonitrile agreed reasonably well with the theoretical molecular weight in N,N‐dimethylformamide. The rate of polymerization increased with increasing polymerization temperature, and the apparent activation energy was calculated to be 59.9 kJ mol^?1. Reverse atom transfer radical polymerization was first used to successfully synthesize acrylonitrile polymers with a molecular weight higher than 80,000 and a narrow polydispersity as low as 1.22. © 2005 Wiley Periodicals, Inc. J Polym Sci Part A: Polym Chem 44: 219–225, 2006     

Scientist up to the highest level

Dr. Miroslav Kyrš, DrSc. passed away prematurely and unexpectedly in August 2006 at age of 75. He was a leading person of the Czech radiochemistry during the second half of the 20th century and his results have of world-wide impact. His diligence, intelligence and permanent activity led him to be at first a laboratory chief and subsequently for about 25 years to be a chief of the Radiochemical Department of Czech Nuclear Research Institute (NRI) at Řež near Prague.     

An Economical Magnetocardiogram System Based on High-To SQUIDs

An economical magnetocardiogram （MCG） system is built in our laboratory. It mainly consists of a MCG data acquisition stage equipped with two high-To superconducting quantum interference device （SQUID） magnetometers, a data processing stage with digital filtering and a one-layer μ-metal magnetically shielded room in conjunction with a high-Tc SQUID based active compensation. Experimental results show that a noise level of pico-tesla in MCG profiles, which is necessary for clinical applications, may be achieved with the system. Moreover, stable and convenient operations of the system are demonstrated with simulating MCG measurements.